| جزء لا | الصانع | التطبيق |
|---|
| MAX503CWG | MaximIC | 5V, low-power, parallel-input, voltage-output 10-bit DAC. |
| MAX708SESA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.93V. Active-low and active-high reset output signal. |
| MAX6318MHUK48BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX797HESE | MaximIC | High-voltage, step-down controller with synchronous rectifier for CPU power. 3.3V and 5V or adjustable output. |
| MAX359EPE | MaximIC | Fault-protected analog 4 channel differential (2 of 8) multiplexer. |
| MAX6309UK41D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.998(min),4.203(max) Nominal timeout period 140ms. |
| MAX5151BCEE | MaximIC | Low-power, dual, 13-bit voltage-output DAC with serial interface. +3V single-supply operation. INL(LSB) +-2. |
| DG301CJ | MaximIC | Dual, TTL compatible CMOS analog switch. |
| MAX6336US16D1-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 1.6V, reset timeout(min) 1ms. |
| MAX4053AMJE | MaximIC | Low-voltage, CMOS analog switch |
| MAX6334UR22D1-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.2V, reset timeout(min) 1ms. |
| MAX231EWE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX1729EUB | MaximIC | ECB and LCD display bias supply with accurate output voltage and temperature compensation. |
| MAX4611CUD | MaximIC | Low-voltage, quad, SPST, CMOS analog switches (four NC switches). |
| MAX693ACSE | MaximIC | Microprocessor supervisory circuit. Reset threshold(typ) 4.4V. |
| MAX6320PUK28DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX642BESA | MaximIC | +12V fixed output, 10W CMOS step-up switching regulator. 10% output accuracy |
| MAX6501UKP105-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage open-drain. Standard temperature threshold(C) +105. |
| MAX3225EEPP | MaximIC | +-15kV ESD-protected, 1microA, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus. |
| MAX1297AEEG | MaximIC | 265ksps, +3V, 2-channel single-ended/1-channel pseudo-differential, 12-bit ADC with +2.5V reference and parallel interface INL(LSB) +0.5, -0.5 |
| MAX194BEPE | MaximIC | 14-bit, 85ksps ADC with 10 microA shutdown |
| MAX643BEPA | MaximIC | +15V fixed output, 10W CMOS step-up switching regulator. 10% output accuracy |
| MAX4108ESA | MaximIC | Ultra-low-noise op amp. 400MHz unity-gain bandwidth. |
| MAX147BCAP | MaximIC | +2.7 V, low-power, 8-channel, serial 12-bit ADC. INL(LSB) +-1. |
| MAX6318MHUK50DY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX4513EPE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX873BCSA | MaximIC | Low-power, low-drift precision voltage reference. 2.5V+-2.5mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX802MCPA | MaximIC | Microprocessor supervisory circuit. 4.40V precision supply-voltage monitor. Power-fail accuracy guaranteed to +-2%. |
| MAX666MJA | MaximIC | Dual Mode 5V or programmable micropower voltage positive with on-chip vow-battery detection circuitry regulator. |
| MAX519BESE | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
